My Account   My Cart       Check Out


Contact Us:  850-439-1708
HOME          CONTACT US          PRIVACY POLICY          PENSACOLA BOAT RAMP
Search:
     





     
Home > Paints, Thinners, & Additives > Primers & Undercoats >
Interlux Pre-Kote Primer
Interlux Pre-Kote Primer

Pre-Kote Primer White




     Item # Description/Size Availability Qty Break Price Options Quantity
    94-4279Q
    Pre-Kote Primer Quart
    In Stock 1 $23.84
    94-4279G
    Pre-Kote Primer Gallon
    In Stock 1 $72.41
    Interlux PreKote primer is used above the waterline prior to painting topsides with Brightside polyurethane, Toplac, yacht enamels, or any one part topside finish on wood, fiberglass, and previously painted surfaces.

    Pre-kote contains microspheres for superior build and hide. Microspheres also make it easier to sand.
    • Finish: Matte
    • Specific Gravity: 1.397
    • Volume Solids: 61%
    • Typical Shelf Life: 2 yrs
    • VOC (As Supplied): 330 g/lt
    • Unit Size: 1 US QUART, 1 US GALLON
    • Number of Coats: 1-2 as needed
    • Coverage (Theoretical) - 450
    • Area Above the waterline
    • Apply with: Brush, roller, or conventional spray
    • Available in White
    This primer requires thinner 333 (for brushing) or 216 (for spraying).

    Drying Information  

    50 Degrees F 

    73 Degrees F 

    95 Degrees F

    Touch Dry  

    3 hours 

    2 hours 

    1 hour

    Overcoating Information 

    min - max time 

    min - max time 

    min - max time

    Brightside 

    12 hours- 

    8 hours- 

    6 hours-

    Pre-Kote 

    12 hours- 

    8 hours- 

    6 hours-

    Toplca 

    12 hours- 

    8 hours- 

    6 hours- 


    PREVIOUSLY PAINTED SURFACES: Sand old surfaces with 120 grade (grit) paper. Remove sanding residue. Wipe with Brushing Liquid 333. Repair surface defects with Surfacing Putty 257. Sand surface, wipe clean.

    BARE WOOD: Sand with 80 grade (grit) paper. Wipe with Brushing Liquid 333. Repair surface defects with Surfacing Putty 257. PLYWOOD: Follow directions for bare wood. Apply Inter-Prime Wood Sealer Clear 1026. MAHOGANY Follow directions for bare wood. Apply Pre-Kote directly to the wood.

    BARE FIBERGLASS: Wipe a small area with a clean rag that has been wetted with Fiberglass Solvent Wash 202. While the surface is still wet, wipe with a clean, dry rag. Continue this process until the entire surface has been cleaned. Sand with 80 grade (grit) paper. Wipe with Fiberglass Solvent Wash 202. Repair surface defects with Interfill Epoxy Filler. Sand surface, wipe clean.

    Method: Apply 1-2 coats. Depending on surface condition. Allow the necessary overcoating time between applications. Sand between primer coats with 120 grade (grit) paper until translucent. Remove sanding residue with a rag dampened with Brushing Liquid 333. Apply finish coats. Sand with 220 grade (grit) paper between Pre-Kote and finish enamel.

    Hints:
    Thinner Brush - Brushing Liquid 333. Spray - Special Thinner 216.

    Cleaner Painted Surfaces - Brushing Liquid 333. Bare Wood - Brushing Liquid 333. Bare Fiberglass - Fiberglass Solvent Wash 202.

    Ventilation and Humidity Control: It is best to paint on warm, dry mornings.

    Airless Spray Pressure: 170-204 bar/2500-3000 psi. Tip Size: 0.48-0.53 mm/19-21 thou.

    Conventional Spray Pressure Pot: Pressure: 3.44-4.08 bar/50-60 psi (gun pressure). Pot pressure (6 ft hose) 8-10 psi. Tip Size: 0.89-1.4 mm/35-50 thou. Siphon Cup: Pressure: 3.44-4.47 bar/50-65 psi - gun pressure. Tip Size: 1.8-2.2 mm/70-85 thou.
    Other Spray pressures listed are recommendations only. The applicator may use any settings which yield the best results for the individual spraying technique and current weather conditions. It is always good painting practice to apply the finish enamel soon after sanding to avoid surface contamination. Always apply at least one coat of Pre-Kote over area treated with Surfacing Putty 257 to seal the putty and eliminate shadows.

    Some Important Points: Pre-Kote is a high solids primer. Avoid a heavy application as this may lead to solvent entrapment. Product temperature should be minimum 10 degrees C/50 degrees F and maximum 29 degrees C/85 degrees F. Ambient temperature should be minimum 10 degreeas C/50 degrees F and maximum 35 degrees C/95 degrees F. Substrate temperature should be minimum 10 degrees C/50 degrees F and maximum 29 degrees C/85 degrees F.

    Compatibility/Substrates: Apply to clean, dry, properly prepared surfaces only. Do not apply over clear epoxy such as Epiglass Epoxy.

    Number of Coats: 1-2 as needed

    Coverage: (Theoretical) - 450 (sq ft/Gal) by brush, 360 (sq ft/Gal) by spray

    Recommended DFT: 2.0 mils dry
    Recommended WFT: 3.5 mils wet

    Application Methods: Brush, Roller, Airless Spray, Conventional Spray - Pressure Pot or Siphon Cup


    Related Items:
    Join our Mailing List
    Related Items:
    Spotlight Items:
    FEATURED
    BRANDS

      
     
     
     
     
     

    HOME    CONTACT US   PRIVACY POLICY     PENSACOLA BOAT RAMP       RETURN POLICY

    Shopping Cart Software by AmeriCommerce.